- 您现在的位置：买卖IC网 > Sheet目录686 > DV1-100 (TechTools)DIGIVIEW LOGIC ANALYZER 100MHZ
22
DigiView User's Guide
Data Channels
Selects which physical channels to assign to the DATA bus.
Enable Channel
Selects which physical channel to assign to the ENABLE. The enable can be disabled if not
used.
Frame SYNC Channel
Selects which physical channel to assign to the FRAME SYNC. The FRAME SYNC can be
disabled if not used. This can be used to identify frame limits.
Clock On
Selects which edge of the clock to use to strobe in then data.
Enable Level
Selects the active level for the Enable signal.
Skip States
Specifies how many states to ignore before starting a frame. Useful for syncing up data that
has no framing signals.
States per Frame
Specifies how many states are in a frame (if fixed). Set to 0 to ignore if other framing
methods are being used.
Frame SYNC starts New Frame on:
Specifies how the Frame Sync signal is used (if enabled). Rising,Falling and Either edges
specify what starts a new frame (and terminates the previous frame). The last two options
specify that one edge starts a frame and the other edge terminates the frame. Any
startframe will automatically end the previous frame. Specifying the endframe just ends it
earlier for aesthetics.
Frame IDLE Timeout (0 to ignore):
A new frame is started if no new states are seen for more than the specified time. Set to 0
to disable. This can be useful if there are no sync lines or field counts but you can see a
consistent pause before each frame starts.
Show Field Idles
Specifies whether idle time between fields should be shown as a hashed field or if the
current field should just extend to the next field.
Show Frame Idles
Specifies whether idle time between frames should be shown as a single center line or if the
current frame should just extend to the start of the next frame.
Reset Colors
This button will reset the colors for this signal so that they will match the currently selected
color theme (see: Color Themes 55 ).
NOTE: Multiple framing methods can be used at the same time. For example, you could use a
frame length specifier and the frames will be broken into the specified lengths. If a timeout is
specified, it will override and terminate a frame if the specified time is exceeded.
? 2014 TechTools
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DV75C-020.0M
OSC TCXO 20.000 MHZ 3.3V SMD
DV75D-020.0M
OSC TCXO 20.000 MHZ 3.3V SMD
E2G0402S
SWITCH ROTARY LEVER 4P-2POS
E3G0603N-2
SWITCH ROTARY 6P-3POS MOMENTARY
E4C-N10
WAFER SW DP-8POS NON-SHORTING 9A
ECAP1AAE
CAP LIGHT WHITE/RED LED
ECLAMP2342N.TCT
IC ESD/EMI PROT LCD INTRFC 16QFN
ECLAMP2357N.TCT
IC ESD/EMI PROT SD CARD 16QFN
相关代理商/技术参数
DV11201-S3
制造商:Foxconn 功能描述:
DV11203-D4
制造商:Foxconn 功能描述:
DV11203-R0
制造商:Foxconn 功能描述:
DV11206-S2
制造商:Foxconn 功能描述: 制造商:Foxconn 功能描述:Electronic Component
DV115K3225T
制造商:SEI Stackpole Electronics Inc 功能描述:- Tape and Reel 制造商:SEI Stackpole Electronics Inc 功能描述:Var MOV 115VAC/150VDC 400A 180V 3225 SMD T/R
DV115K4032T
制造商:SEI Stackpole Electronics Inc 功能描述:Var MOV 115VAC/150VDC 1200A 180V 4032 SMD T/R
DV11603-G4-4F
制造商:Foxconn 功能描述:DSUB Right Angle Type, T/H, 2.41mm [.100"] Pitch, 78 Pos. Color: Black
DV11A11B
制造商:MURATA 功能描述:TRIMMER